Skip to main content

The unit circle: sine, cosine, tangent, and cotangent

2026-10-22 Cùng Học Toán Comments: 0

Read signed trigonometric values from the unit circle and understand the domains and geometric axes of tangent and cotangent.

High schoolTrigonometry

Content updated: October 22, 2026

The unit circle associates an angle with a point having specified coordinates. Sine and cosine can then be read from projections; tangent and cotangent additionally require nonzero denominators.

Learning goals: determine the rotation direction, read coordinates and signs, interpret tangent and cotangent geometrically, and check their domains.

Prerequisites: coordinates in the plane, angles, and radian measure.

On this page: Definition · Method · Examples · Practice · Further learning

1. The unit circle and the point representing an angle

In the coordinate plane $Oxy$, the unit circle has center $O(0;0)$ and radius $1$, hence equation $x^2+y^2=1$. Choose the initial point $A(1;0)$ on the positive x-axis. The positive direction is counterclockwise; the negative direction is clockwise.

Rotating the ray $OA$ through a directed angle $\alpha$ gives a terminal ray meeting the circle at $M$. By definition, $M(\cos\alpha;\sin\alpha)$. The horizontal axis reads cosine and the vertical axis reads sine. These are signed coordinates, not necessarily ordinary lengths.

A full turn is $2\pi$ radians, or $360^\circ$. The angles $\alpha+2k\pi$, with $k\in\mathbb Z$, have the same terminal point. A point therefore does not determine a unique angle measure.

2. Projections and the tangent and cotangent axes

Let $M_1=(\cos\alpha;0)$ and $M_2=(0;\sin\alpha)$ be the projections of $M$ onto the axes. With their usual positive coordinate directions, $\overline{OM_1}=\cos\alpha$ and $\overline{OM_2}=\sin\alpha$. The overline denotes a signed length here; the ordinary lengths $OM_1=|\cos\alpha|$ and $OM_2=|\sin\alpha|$ are nonnegative.

Since $M$ lies on the circle of radius 1, $\cos^2\alpha+\sin^2\alpha=1$. Both coordinates lie in $[-1;1]$. Cosine’s sign depends on the left or right half-plane; sine’s sign depends on the lower or upper half-plane.

The tangent axis is the line $x=1$ through $A$, directed upward. When $\cos\alpha\ne0$, the line $OM$ meets it at $T=(1;\tan\alpha)$, where $\tan\alpha=\sin\alpha/\cos\alpha$. Use the entire line $OM$, since the ray $OM$ may not meet $x=1$. When $\cos\alpha=0$, tangent is undefined.

Set $B=(0;1)$. The cotangent axis is the line $y=1$ through $B$, directed to the right. When $\sin\alpha\ne0$, the line $OM$ meets it at $S=(\cot\alpha;1)$, where $\cot\alpha=\cos\alpha/\sin\alpha$. Under their respective nonzero-denominator conditions, the signed lengths satisfy $\overline{AT}=\tan\alpha$ and $\overline{BS}=\cot\alpha$. If $\sin\alpha=0$, cotangent is undefined.

The unit circle and points representing anglesA circle with center O and radius 1. A is on the right and B is above. M represents π/6. Its two projections determine the cosine and sine coordinates.xyOA (1; 0)B (0; 1)M (√3/2; 1/2)M₁M₂π/6x-coordinate: cos αy-coordinate: sin αPositive angles turn counterclockwise. Radius = 1.
The new diagram illustrates the angle $\pi/6$: the point $M=(\sqrt3/2;1/2)$ and its two projections. It shows sine and cosine only; the tangent and cotangent axes are defined by coordinates in the text.

3. Examples of reading values

Example 1. The angle π/6

For $\alpha=\pi/6$, the terminal point is $M=(\sqrt3/2;1/2)$. Thus $\cos\alpha=\sqrt3/2$, $\sin\alpha=1/2$, $\tan\alpha=1/\sqrt3$, and $\cot\alpha=\sqrt3$. Both denominators are nonzero, so tangent and cotangent are defined.

Example 2. A negative coordinate

For $\alpha=2\pi/3$, the terminal point has coordinates

$$\left(-\frac12;\frac{\sqrt3}2\right).$$

The point lies in quadrant II. Thus cosine is negative, sine is positive, and tangent and cotangent are negative. The distance from $O$ to the horizontal-axis projection is $1/2$, whereas the cosine coordinate is $-1/2$; its minus sign must be retained.

Example 3. A point on an axis

At $\alpha=\pi/2$, the terminal point is $B=(0;1)$. Sine equals 1, cosine equals 0, tangent is undefined, and cotangent equals 0. At $\alpha=0$, sine equals 0, cosine equals 1, tangent equals 0, and cotangent is undefined. A zero value is different from an undefined value.

4. Practice

  1. Find the coordinates of the point representing $-\pi/2$; state tangent and cotangent if they are defined.
  2. Do $\pi/6$ and $13\pi/6$ have the same terminal point?
  3. Does $M=(-3/5;4/5)$ lie on the unit circle? Find tangent and cotangent of an angle with this terminal point.
Hints and answers
  1. The point is $(0;-1)$. Tangent is undefined because cosine is zero; cotangent is zero because sine is nonzero.
  2. Yes. Their difference is $2\pi$, exactly one full turn; the corresponding sine and cosine values agree.
  3. Yes, because $9/25+16/25=1$. Tangent is $-4/3$ and cotangent is $-3/4$; both denominators are nonzero.

5. Common mistakes

Do not replace signed coordinates by always-positive lengths. Do not assume that a point represents only one angle. The tangent axis is $x=1$ and the cotangent axis is $y=1$, with the chosen orientations; their intersection conditions are exactly the nonzero-denominator conditions. Use radians or degrees consistently.

6. Further learning

Representing angles on the unit circle (English lesson) · Identities for related angles (English lesson) · Trigonometric identities (English lesson).

Original video lesson (Vietnamese)

Leave a Reply

Your email address will not be published. Required fields are marked *